SAE J30 R6 is one hose specification sold in twelve different bores, and the bore is the choice that matters most. The construction is the same across all of them, so once you know R6 is the right grade, the only real decision is the size. This guide lists every bore we stock, what each range is generally used for, and how to match the hose to the spigot it has to fit.

What stays the same across every R6 size

Every bore listed below is built to the same specification, so you can pick the size without re-checking the material each time:

  • Applications: flexible hose for the flow of fuel, oil and industrial water, for general contact with fuel and oil.
  • Tube: synthetic rubber, black, smooth, oil resistant.
  • Reinforcement: synthetic cord.
  • Cover: synthetic rubber, black, smooth, resistant to oil, weather and ozone.
  • Temperature: -40°C to +100°C.
  • Standard: SAE J30 R6.

Each bore is priced per metre ex VAT, and the product page offers a 1 m option and a 50 m option. The price rises with the bore, so check the product page for the size you need.

The full list of SAE J30 R6 bores

These are the twelve inner diameters on sale, each with its own product page:

  • 3.2 mm
  • 4 mm
  • 5 mm
  • 6 mm
  • 7 mm
  • 8 mm
  • 10 mm
  • 12.7 mm
  • 16 mm
  • 18 mm
  • 22 mm
  • 25 mm

Some of these follow inch sizes: 12.7 mm is a half inch, and 25 mm is near enough an inch. If your spigot measures one of those figures, the part may have been made to inch sizes, and the matching bore is the one to buy.

Which bore range suits which kind of job

The bore you need is set by the spigot, not by the job, so treat the ranges below as a general guide to where each size tends to turn up rather than a fitment list.

3.2 mm to 6 mm: small lines

The 3.2 mm page describes it as suited to machinery, vehicles and equipment where space is limited. The 4 mm and 5 mm pages describe the hose for various machinery and vehicles, and the 6 mm page for fuel and oil transfer applications.

7 mm to 10 mm: general fuel and oil lines

The 7 mm and 10 mm pages describe the hose for fuel and oil transfer applications. The 8 mm page describes it as suited to applications requiring a larger flow rate, including fuel lines, machinery and vehicles.

12.7 mm to 25 mm: larger bores for transfer

The large bore pages describe the hose as for fuel and oil transfer applications, and the 25 mm page as designed for the conveyance of fuel, oil and industrial water.

How to match the bore to the spigot

Hose is sized by its inner diameter, and that figure has to match the outside diameter of the spigot it pushes onto. A few rules keep this simple:

  • Measure the spigot, not the old hose. Use callipers across the outside of the spigot, behind any barb. An old hose that has been on a fitting for years is stretched and will read large.
  • If you only have the old hose, measure the bore at a clean, uncut end through the centre, not across a chord.
  • Between two sizes, go to the smaller one. Rubber hose stretches onto a spigot and grips. A bore slightly under the spigot gives a tight joint a clamp can finish; a bore over it is hard to seal, even with a tight clamp.
  • Size the clamp to the hose outside diameter, measured with the hose on the spigot, and use one at each joint. Pick a clamp whose range brackets that figure rather than ending on it.

The full method, with the common mistakes, is in how to measure hose bore.

Where R6 must not go: inside the tank

Every R6 size carries the same note on its page: not designed to be submerged in gasoline. R6 is for general contact with fuel and oil, so it should not sit in fuel inside a tank. Choosing a different bore does not change that. If the hose will sit in fuel, read SAE J30 R6 or R10: which fuel hose goes in the tank before you order.

Also route any size without kinks, keep it away from sharp edges and hot surfaces outside the -40°C to +100°C range, and inspect older lines for cracking, especially at the clamps.

Ordering the right size

Open the product page for your bore, choose the 1 m option and set the quantity to the number of metres you need, or the 50 m option for a full length, and add it to the basket. You can also use the order on WhatsApp option on the page, or ask us there for a specific cut length. Stocked lines ordered before 14:00 on a working day are packed the same day. Cut lengths are prepared to order and can take an extra working day before they leave us. Cut-to-length hose cannot be returned unless it is faulty, so measure the spigot before you buy.

If you are unsure of the size, call +44 (0) 7717 217388 or use the Ask about this link on the product page for your bore (for example the 8 mm R6 page), and tell us three things: the spigot or bore measurement, the length you need, and what will run through the hose.