If you are moving diesel out of a storage tank, a site bowser or a drum, the hose between the pump outlet and the nozzle or receiving tank does a lot of work. It is dragged across yards, left out in the weather and filled with fuel day after day. This guide covers the two families we sell for this job, large bore SAE J30 R6 in 22 mm and 25 mm, and the Oil Delivery Hose, and the points to check before you order a length.
The two options for diesel transfer
SAE J30 R6, 22 mm and 25 mm bore
The Oil resistant hose SAE J30 R6 (22mm) and the Oil resistant hose SAE J30 R6 (25mm) are the large bore end of our R6 range. Both are described as a flexible hose suitable for flow of fuel, oil and industrial water, for general contact with fuel and oil. That makes them a sensible choice for a diesel transfer line.
- Tube: synthetic rubber, black, smooth, oil resistant.
- Reinforcement: synthetic cord.
- Cover: synthetic rubber, black, smooth, oil, weather and ozone resistant, which matters for a hose kept on a bowser outdoors.
- Temperature: -40°C to +100°C.
- Standard: SAE J30 R6.
The R6 pages also note that this hose is not designed to be submerged in gasoline.
Both sizes are in stock and priced per metre, with 1 m and 50 m length options on the page.
Oil Delivery Hose
The Oil Delivery Hose 10 Bar is a rubber hose suitable for delivery of oil and oil derived products in factories, vessels and other industrial applications. It also has a black, smooth, oil resistant synthetic rubber tube and synthetic cord reinforcement, but its cover is oil and abrasion resistant with a cloth impression. Its temperature range is -30°C to +80°C. This hose is not listed with a price: it is price on request, so you tell us the bore and length and we come back with a price and lead time.
Which one suits your job
For most tank, bowser and drum transfer where the pump outlet takes a 22 mm or 25 mm hose, the R6 lines are the straightforward choice: in stock and ordered online. The weather and ozone resistant cover suits hose that lives outside on a trailer or next to a yard tank.
The Oil Delivery Hose is worth asking about when the hose is part of an industrial installation, in a factory or on a vessel, or when the line is dragged over rough ground and an abrasion resistant cover is the priority. Because it is priced to order, ask early if you have a deadline.
Whichever you choose, compare the temperature range with where the hose will be used. The R6 range goes down to -40°C and up to +100°C; the Oil Delivery Hose covers -30°C to +80°C.
What to check before you order
The bore of the pump outlet
Hose is sold by its inner diameter, so match the bore to the outlet or tail of your pump and to the nozzle or fitting at the far end. Do not guess from the outside of an old hose. If you are unsure, our guide on how to measure hose bore shows how to get the inner diameter right. A hose that is too large for the tail will not seal however hard you tighten the clamp, and one that is too small will not go on.
Temperature range
Think about the coldest winter morning and the hottest day the hose will see, including sun on a dark hose lying on concrete. Pick the line whose stated range covers both.
Length of run
Measure the actual route from the pump to the furthest point you need to reach, following the ground, round corners and up onto the vehicle or tank, then add a little slack so the hose is not pulled tight at either joint. Do not order a long coil just in case: extra hose is more to drag, coil and store, and cut-to-length hose cannot be returned unless it is faulty.
Clamps at every joint
Use a clamp at each end, sized to the outside diameter of the hose, not the bore. Seat the hose fully over the tail before tightening, and check the clamps again after the first few uses as the rubber settles.
What not to do
- Do not use water or garden hose for diesel. Use a hose whose page states it is oil resistant and suitable for fuel. A hose made for water is not stated as suitable for diesel.
- Do not ignore the R6 note. The R6 pages state that this hose is not designed to be submerged in gasoline.
- Do not route it over sharp edges or leave it kinked. Run the hose without tight bends and protect it where it crosses a tank lip, drum rim or trailer edge.
- Do not ignore wear. Inspect the cover and the ends regularly and replace a length that is cracked, swollen or cut.
How to order or ask
To order, choose the length option on the 22 mm or 25 mm SAE J30 R6 page. Stocked lines ordered before 14:00 on a working day are packed the same day, and cut lengths are prepared to order. For the Oil Delivery Hose, send an enquiry from its page with the bore, the length and what is going through it, and we will reply with a price and lead time. If you are not sure which to choose, call +44 (0) 7717 217388 and tell us the pump outlet size, the length of the run and where the hose will be used.


